Forgot PLDT admin and adminpldt password? Can’t access PLDT home Fibr anymore? Yes, you can just reset but it’s not practical. It’s a bit of a hassle to start setting up the PLDT router again. From changing WiFi password again, SSID, and admin password. It’s a waste of time and effort.
Advertisements
How are you going to recover PLDT admin password? The good news is you are in the right place at the right time. I will teach you on how to recover your forgotten PLDT admin and adminpldt password using TelNet. No hard reset or soft reset needed! Let’s do it!
Things to remember before we access PLDT Fibr using Telnet
I need you to read the, How to enable TelNet on Windows 7, 8, 8.1 and 10. To equip you of the best armament as we go on. You will learn from that post on how to enable Telnet on Windows OS, which is an essential part of this guide and the danger of using Telnet.
Tips 💡 These are the things that we should do to recover our forgotten PLDT Home Fibr admin and adminpldt passwords.
Advertisements
- Enable Windows Telnet
- Access PLDT router with 192.168.1.1/fh URL
- Latest Fibr username and passwords
- Enable Telnet switch and Web admin switch
- Open an elevated command prompt
- Another login credentials
- Telnet commands
- Change directory command
- Telnet user command
Forgot adminpldt password?
Note⚠️: This tutorial is intended for PLDT subscribers only. If you are not one of them, please have some respect for yourself this guide is not for you. Thank you!
In this guide, you will learn the step by step method on how to recover forgotten PLDT Home Fibr adminpldt password. Please follow the guide carefully.
① As I have mentioned a while ago, please enable Telnet on your Windows PC.
② Let’s type the I.P. address of our gateway or modem/router. It’s 192.168.1.1/fh or https://192.168.1.1/login.html.
Advertisements
③ If you see a privacy or not secure error, refer to this, PLDT Fibr Privacy error solution.
④ Login using the following credentials: PLDT superadmin usernames and passwords.
⑤ debug switch , enable both ➔ Telnet switch and Web admin switch ➔ don’t forget to click apply respectively.
⑥ Press ➔ Windows logo + R ➔ Type “cmd” ➔ Press Ctrl+Shift+Enter to open elevated command prompt or run it as administrator. How will you determine the difference between elevated and unelevated CMD? I got that covered here: elevated and not elevated command prompt.
⑦ In your CMD ➔ type telnet 192.168.1.1 then hit ➔ enter. You will then see a login prompt.
⑧ Input gepon as username and password. Don’t foget to hit enter after each command.
⑨ Then type ➔ enable and the password is gepon.
⑩ Now, let’s change the directory to web by typing ➔ cd web .
⑪ This is it! The command that will reveal our PLDT home Fibr gateway’s full admin password. Are you ready? Let’s type ➔ get web admin username adminpldt and ↩ | enter .
Forgot PLDT admin password?
⑫ To recover your basic admin password, input ➔ get web user username admin and ↩ | enter .
💡Tips: If you encounter “unknown command error” type ➔ ddd➔ Enter↩. But this may not work on PLDT HG model with software versions RP2613 and RP2602.
What do you think about my PLDT gateway’s password? Now, that you know your router’s password, accessing your modem/router isn’t hard anymore. You can follow these guides: 8 easy steps: How to access PLDT Fibr ONU Router and How to Access PLDT Fibr Router RP2631 version.
When you are done accessing and fine-tuning your PLDT Fibr’s settings, I would recommend you to disable Telnet on Windows, and on your router’s debug switch. Let’s be safe than sorry.
Ano says
March 19, 2020 at 9:29 am
I think ng update na naman si PLDT. Waiting for your new post boss.
racky says
sa mga hindi maka connect using gepon try nyo username: gpon , pass: gpon
yan sa akin .
GrandPhartz says
gepon user/password not working on new install of HG6245D router
Mikey says
Got my telnet pw for the adminpldt account and did the following after disabling Telnet:
-Restarted my router
-Went to the superadmin account and enabled Web Admin switch
-Logged back just to make sure Web admin switch was enabled, and it was. (Re-typed the URL too just to be safe)
-Re-typed the URL 192.168.1.1/fh instead of reloading as suggested to input the adminpldt credentials
-Used adminpldt and my Telnet PW
Still getting an error on login with the username and pass. The z6dUABtl270qRxt7a2uGTiw was shown to be my pw by Telnet since I never really changed it back when I still had access to adminpldt.
Is there something going on here?
I.C Tiempo says
Hello Mikey,
You did everything right as per the instruction. You must be able to login using the username and password. I am not sure what’s wrong. But let’s try these;
– Clear your browser cache or all the history, set it to “beginning.”
– Then, login into your Debug switch -> “web admin switch,” click the “restore or restore all.”
– If it’s done, go back to Debug switch and enable the web admin switch again since we lost that setting after the restore all process.
– Logout and Re-typed the URL 192.168.1.1/fh.
– You will now be prompted to change your adminpldt password.
– Change it to your desired password. I hope this helps.
mark says
sir hindi gumagana yung gepon na pw and user bad user name and pw po lagi ano pong solution pls reply asap ty
Cris says
Baka meron n password for rp2602 wala po kasi ako pc kaya d aq makapag telnet salamat.
Jhon says
same tyu boss