Forgot PLDT admin and adminpldt password? Can’t access PLDT home Fibr anymore? Yes, you can just reset but it’s not practical. It’s a bit of a hassle to start setting up the PLDT router again. From changing WiFi password again, SSID, and admin password. It’s a waste of time and effort.
Advertisements
How are you going to recover PLDT admin password? The good news is you are in the right place at the right time. I will teach you on how to recover your forgotten PLDT admin and adminpldt password using TelNet. No hard reset or soft reset needed! Let’s do it!
Things to remember before we access PLDT Fibr using Telnet
I need you to read the, How to enable TelNet on Windows 7, 8, 8.1 and 10. To equip you of the best armament as we go on. You will learn from that post on how to enable Telnet on Windows OS, which is an essential part of this guide and the danger of using Telnet.
Tips 💡 These are the things that we should do to recover our forgotten PLDT Home Fibr admin and adminpldt passwords.
Advertisements
- Enable Windows Telnet
- Access PLDT router with 192.168.1.1/fh URL
- Latest Fibr username and passwords
- Enable Telnet switch and Web admin switch
- Open an elevated command prompt
- Another login credentials
- Telnet commands
- Change directory command
- Telnet user command
Forgot adminpldt password?
Note⚠️: This tutorial is intended for PLDT subscribers only. If you are not one of them, please have some respect for yourself this guide is not for you. Thank you!
In this guide, you will learn the step by step method on how to recover forgotten PLDT Home Fibr adminpldt password. Please follow the guide carefully.
① As I have mentioned a while ago, please enable Telnet on your Windows PC.
② Let’s type the I.P. address of our gateway or modem/router. It’s 192.168.1.1/fh or https://192.168.1.1/login.html.
Advertisements
③ If you see a privacy or not secure error, refer to this, PLDT Fibr Privacy error solution.
④ Login using the following credentials: PLDT superadmin usernames and passwords.
⑤ debug switch , enable both ➔ Telnet switch and Web admin switch ➔ don’t forget to click apply respectively.
⑥ Press ➔ Windows logo + R ➔ Type “cmd” ➔ Press Ctrl+Shift+Enter to open elevated command prompt or run it as administrator. How will you determine the difference between elevated and unelevated CMD? I got that covered here: elevated and not elevated command prompt.
⑦ In your CMD ➔ type telnet 192.168.1.1 then hit ➔ enter. You will then see a login prompt.
⑧ Input gepon as username and password. Don’t foget to hit enter after each command.
⑨ Then type ➔ enable and the password is gepon.
⑩ Now, let’s change the directory to web by typing ➔ cd web .
⑪ This is it! The command that will reveal our PLDT home Fibr gateway’s full admin password. Are you ready? Let’s type ➔ get web admin username adminpldt and ↩ | enter .
Forgot PLDT admin password?
⑫ To recover your basic admin password, input ➔ get web user username admin and ↩ | enter .
💡Tips: If you encounter “unknown command error” type ➔ ddd➔ Enter↩. But this may not work on PLDT HG model with software versions RP2613 and RP2602.
What do you think about my PLDT gateway’s password? Now, that you know your router’s password, accessing your modem/router isn’t hard anymore. You can follow these guides: 8 easy steps: How to access PLDT Fibr ONU Router and How to Access PLDT Fibr Router RP2631 version.
When you are done accessing and fine-tuning your PLDT Fibr’s settings, I would recommend you to disable Telnet on Windows, and on your router’s debug switch. Let’s be safe than sorry.
Mark Bonilla says
September 24, 2019 at 11:54 pm
I was able to follow and enable the telnet and web admin access once but then when I restarted the router I could no longer login using the credentials provided above. Is it possible na nag update po firmware nya and nabago na initial default password para sa admin account?
I.C Tiempo says
Hello Mark, please be guided that after the router restart the webadmin switch and telnet switch will reverse back to DISABLE. Moreover, web admin switch will automatically disabled after certain period of time (about 3 to 4 hours since it was enabled). So, you have to repeat the instruction again to access your adminpldt.
chiclet says
I got my adminpldt password using telnet pero username and password error pa din po. what could be wrong?
I.C Tiempo says
After you enable web admin switch and logged out, type again the 192.168.1.1/fh before typing your adminpldt and password. You will be redirected to login.html but that’s fine.
ronronronron says
i still do that but still username pasword error, i got the password from telnet. help pls
I.C Tiempo says
Hi, kindly re-type the URL (192.168.1.1/fh) before entering the password.
Ray says
Nag switch na ko nung isang araw sa web admin and nakakalogin nako as adminpldt nung isang araw. Ngayon di nako maka login as adminpldt. Now tnatry ko ulit tingnan yung Web Admin Switch pero blank lang nakikita ko lagi: https://prnt.sc/p8lq43
I.C Tiempo says
Please refer at the bottom part of this post:https://www.techchore.com/access-pldt-fibr-router-rp2631-version/.
PG Olivier Bulfa says
gepon is not working for me huhuhu
bad username and password
i have rp2602
PG Olivier Bulfa says
it also says the “get admin…” command is Unknown 🙁 huhu pls help
Ace Laurence Crisostomo says
i tried it, but it didnt work, ung adminpldt na username tapos password na galing diyan kay cmd sa telnet tinry ko ilogin kay 192.168.1.1/fh ang sinasabi niya ay username or password error!
I.C Tiempo says
This is for RP2627 and RP2631 software version.
james says
sir what user name you will log in if your ihateyouilove you is the pass, so the user name you will log is adminpldt?
I.C Tiempo says
Precisely…?